From the switch it's just a simple 90 degree turn, it pops out, you disconnect your connector, reverse the procedure to put it back together. Its Brake Light Switches are not only built to last, but also can perfectly complement your vehicle. He might have thought that the hazard lights switch should have lit up with the flashers, but on the Disco the only indication is the two direction flashers in the instrument binnacle, but you might have to provide some documentary evidence say from you owner's handbook to substantiate your claim. I was thinking of wiring the brake light straight to the rear lights but this disco has abs and the likes so had to do a proper job. I am now going into my third winter of no false messages now since I replaced the switch. Many European vehicles use this feature to illuminate the outside corner during parking.
The rest of the lights are fine it's just the two side brake lights and the high level light that don't work. But yes I agree, cooler temperatures seem to be when the brake light switch starts to act up. It was then just a matter of removing the old switch by twisting it like that and then withdrawing it from its retaining bracket. They are substantially different in shape and size. Also check your tail light bulbs - that all filaments are standing vertically as you can see them thru the red plastic. Feb 22, 2017 Had the same problem with my 03 Disco. Why Brake Light Switch replacement is so important.
Decided to post a fresh post with my guide and pictures in it. It is mounted to the brake booster like a big black doughnut. Warning lights for hill descent control, traction control and cruise control could also light up. Remove brake light switch from pedal bracket. This way when you go to change it you actually have an opening right here in the dash, and you're looking right at the brake light switch. Ordered new light switch and the bugger doesn't appear to fit! Buying new Land Rover parts from www.
The booster is attached to the front of the pedal box. Switch sorted and replaced all in around an hour. You may, however, visit our site anonymously. Therefore, attempt to gently pull all connectors apart, and if they are loose, they will probably come apart in your hands. This brand offers the best line of replacement product for your damaged unit or component. Source: What information do we collect? In my case the lights were out, but a cheap trailer rental did the damage.
At Car Parts Discount, we have live customer service members here with enough expertise to help you select the appropriate Land Rover Discovery part for your project or repair. Could be a sign of the brake switch failure. Lift the bonnet, and over on the right side you'll see your brake master cylinder. To remove, push the pedal forward, there is a sleeve that has to be pulled forward, and then the switch removes out the back. The vehicle in your driveway symbolizes the best in class when it comes to all the vehicles in today's marketplace.
We may also release your information when we believe release is appropriate to comply with the law, enforce our site policies, or protect ours or others rights, property, or safety. The job gets bigger but looks like I caught it just in time. Refitting is a reversal etc. Over to your right against the center console this carpeted piece is part of the lower panel, and it is held in by a snap clip which you grab from the back side, you'll pull, and that will release. And there probably several other ways I haven't thought of. Being a push-button switch, it acts as the gate through which current travels to your brake lights; making them turn on when you press on the brake pedal.
However, non-personally identifiable visitor information may be provided to other parties for marketing, advertising, or other uses. Look under brake pedal arm for small plastic thing with a button. Posted on Jul 08, 2011 land rover used a vacuum set up check the vacuum line at the actuator, usually crack at the actuator, cut end off and put back on. This does not include trusted third parties who assist us in operating our website, conducting our business, or servicing you, so long as those parties agree to keep this information confidential. I have tried a new known to be good as i borrowed it from a simular vehicle brake switch. Had what I thought was a failed brake light switch on my '96 Defender 90.
The cause of failure has been identified as excessive electrical load when a trailer has been connected to the circuit. Then you can firmly reconnect the connector. Do we disclose any information to outside parties? Here's my definitive guide, couple of pictures are from other sites. How do we protect your information? Disconnect multiplug from brake light switch. The loom was connected up and the ignition turned on.