Otherwise you'll probably still need someone to come around but they are likely to charge you a lot more to clean it up. Guide Stepping Back Through the Menus If you are in a Menu location, eg. Day zones are those which operate only during periods when the Area is disarmed and are normally used as door bells and shop minders etc. Guide results of the walk-test will be saved in the memory event buffer and can be viewed by accessing memory display mode to verify which detectors were triggered during walk-test mode. Guide Input Options Different Input Configurations The Runner 8 has nine separate programmable monitored analogue inputs. Guide Software change Update Notice Software Update V9. Holidays can override the time-zone function on the programmed day.
Addresses P151E - P200E are used to map the user code to the required Time Zones. Zone doubling is not available when vibration settings are used. To start viewing messages, select the forum that you want to visit from the selection below. All output modifiers such as reset timers and lock out functions are maintained and will determine the behaviour of the assigned output. When kissed-off or the maximum re-tries reached, move forward to the next step. The panel is monitoring the line at all times and 15 seconds after the last key press it will automatically hang up the line.
Purchaser understands that a properly installed and maintained product can only reduce the risk of burglary, robbery or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss or damage as a result. If the option is turned on at this address then an unsealed condition will inhibit the panel from arming until the zone is sealed. An example of this connection method is shown below. Guide Option 2 button can Arm Stay Mode - This option enables single button Arming of Stay Mode using the button. P835E Answer incoming call - provided a user with option 5 set.
There is also a manual answer function described on page 56. Clearly the configuration has become corrupt to it was never set up properly in the first place. Guide zone can activate during the exit time thereby starting an entry delay on the same zone which means the user might not be aware of the pending alarm and leave the premises. Guide Armed by User 4+2 Reporting Code P16E 1-100E 4+2 Arm Code for Users 1-100 Disarmed by User 4+2 Reporting Code P17E 1-100E 4+2 Disarm Code for Users 1-100 Learn Radio Pendant Codes P18E 21-100E Learn Radio Pendant Codes for Users 21-100. ¿me podias decir como se entra en modo de programación con el backdoor o como puedo resetear el código de instalador al original 000000 para poder modificar los números de teléfono a los que llama la alarma? Guide When you are at the desired main menu heading, press to access the data program location.
There are no warranties, expressed or implied, of merchantability or fitness for a particular purpose or otherwise, which extend beyond the description on the face hereof. Guide Option 2 Report Supervised Radio Alarm - If this option is on the panel will report a Supervised radio Alarm see P25E4E. You can program the text for all zones in the same way. Option 4 Code required to arm area - If this option is off the partition can be shortcut armed. If no further steps, stop. Option 3 Report Zone Inactivity Alarm - If this option is on the panel will report a Zone Inactivity Sensor-watch Alarm see P163E. It always comes up with Stay on and never goes into installer mode.
They can also include some special functions or characters as per the chart below. If more than one zone is set-up as a two trigger zone, then a single trigger from two separate zones within the two trigger time can also cause an alarm. This delay can be used to prevent false alarms from reporting if the alarm is cancelled before this delay expires. Each User can have different privileges based on the options assigned to the User at address P5E. A zone defined as two trigger at this address will only cause an activation if one of the following conditions are met; The zone is triggered twice within the two trigger time period as defined by Address P534E, P535E or P536E Any two zones defined as two trigger activate once each within the two trigger time period as defined by Address P534E, P535E or P536E. Guide If Stay Mode is Armed and a Stay Mode delay zone triggers the entry delay it can also beep the keypad buzzer to warn that the entry delay is counting down and the alarm should be turned off. Any comments on this site please click below to email me.
If Output 1 or 2 are used for the Audible walk-test indication and a horn speaker is connected to the output see P37E1 or 2E option 1 , the siren on the output will give a single tone for the chirp instead of the swept tone used for alarms. The program addresses are in numerical order with page references beside them so you can get more detailed information if required. Howdy, I recently purchased a property with one of these alarms. Guide P125E must be set to type 3 2k2. Guide Night Monitor Keypad The Night Monitor Keypad is designed to be a simple night arming station typically used in a bedroom situation.
P701E 1-8E Radio user 1 to output 1-8 - Where options 1-8 represent outputs 1-8. This will release the bottom edge of the housing enough for you to unclip the top. Guide You can now enter an Output name maximum of 16 characters. The plastic housing has a hinged front lid to cover and protect the rubber buttons when not in use. This will overwrite the previous code but maintain the user permissions as mapped to that user number. Program mode access is inhibited if any part of the system is Armed. Without your help this site does not exist.
Guide program the keypad address you must first connect the reader to the panel via the keypad buss. Guide Line Out These terminals are used to connect telephones and other communication equipment to the incoming phone line via the panel dialler circuit. The panel can have up to 100 proximity tags key-ring style card , or proximity cards loaded into the system. It nearly always ends in tears. This is intended as a quick guide to finding a program address. . Option 2 Domestic Dial - If this option is set for the telephone number, the panel is expecting to dial a residential telephone number when an alarm occurs.