Each version have 1 to 10 different questions or more. Router show startup-config startup-config is not present Why does the router respond with the startup-config is not present message? Router config Now you can make any configuration on the Cisco router. To connect to Cisco Router Console in Cisco Packet Tracer, we can easily do this from the cable options. While they are writing someting on the router, it sometimes print something on the secreen and divides your writings. Similarly, the command router show ip interface brief gives us the information about the interfaces of the router. Use end command to return in privileged exec mode. It supports multiple lines for connection.
Is there a place where I can find a list of commands? Next we have to open the Ethernet ports to allow communication. Router config telephony-service Router config-telephony auto assign 1 to 5 Router config-telephony ex Router config ephone-dn 1 Router config-ephone-dn number 1111 Router config-ephone-dn exit Router config ephone-dn 2 Router config-ephone-dn number 2222 Router config-ephone-dn exit Router config ephone-dn 3 Router config-ephone-dn number 3333 Router config-ephone-dn exit Hello Christina, first of all thanks for taking interest in my Blog. You can also click Check Results in the instruction window. Router config-if description Development department This command is optional. Many new engineers complaintive about the logging synronization of the console.
Switch config interface vlan 1 Switch config-if ip address 192. This way, you can easily manage the Cisco Router over the network. Step 5 We connected one end of the console cable to the laptop. Today, there are also converters for rollover cable. Due to length of this article we will include them in next articles with their respective topics. However, because many of the privileged commands configure system parameters, privileged access should be password-protected to prevent unauthorized use.
They are virtual, in the sense that they are a function of software — there is no hardware associated with them. In our previous articles, we talked about and. Hint: fill in the subnet number, then the host address. Question mark to list all available commands If prompt returns with parameters excluding that means it requires more parameters to complete this command. Secure privilege exec mode with password Along with access lines we can also secure privilege exec mode with password.
Set bandwidth for the interface. If your router supports this port use following commands to secure it. We have two commands to configure the password. But to make configuration, you need to enter also teh below command under enable mode: Router configure terminal Enter configuration commands, one per line. Router show ip route Routers use routing table to take packet forward decision.
Step 10 After configuring to Cisco Router using console cable in packet tracer, we need to specify the password for the Cisco console security. Address information will be easy to compute with the subnet number filled in first Maximum number of usable subnets including the 0th subnet? What command do you use? This will save you lots off typing although it is not always necessary to have each word in a command completely spelled out. If you are not prompted for a password, what console line command did you forget to configure? How to Connect to Cisco Router Console in Cisco Packet Tracer? Topology Objectives Part 1: Verify the Default Router Configuration Part 2: Configure and Verify the Initial Router Configuration Part 3: Save the Running Configuration File Background In this activity, you will perform basic router configurations. Type no shutdown At this point our router is configured properly. We can use this features to list all available commands and parameters those are associated with show command.
It will show you which of all the available commands are for the command mode you are in. You can practice with banner motd command. If not, analyze the output and determine which commands were not done or were entered incorrectly. Router show hosts This command displays names and addresses of the hosts on the network that you can connect. In any mode, you can obtain a list of commands available on that mode by entering a question mark? Advertisements To explain basic router configuration commands, I will use packet tracer network simulator software.
Router config-if no shutdown Turns interface on Serial cable is used to connect serial interfaces. All interfaces are set to off on startup. Cisco Router Newbie : How to Configure Console Connection Options? Cisco Router Newbie : How to Give a Password to a Router? We will talk about later on. This command displays routing table. Show command supports several other parameters to display command specific information. I want to ask you that did you copied above configuration in your scenario? The commands are the same as you configured on a switch.