Genie specifications require that this procedure be performed every 2000 hours or every two years, whichever comes first. Result: The alarm does not sound. Failure to install the counterweight after installing the boom assembly will compromise machine stability resulting in the machine tipping over. Place a check in the appropriate box after each part is completed. Symbols Legend Safety alert symbol—used to alert personnel to potential personal injury hazards. The primary boom could become unbalanced and fall if not properly supported when removed from the machine.
Do not allow oil to squirt or spray. Failure to perform the maintenance procedures can lead to poor engine performance and component damage. Note: There may be a 2 second delay before the overload indicator lights flash, the alarm sounds and the engine shuts off. Swing the engine tray out away from the machine. After this interval, refer to the maintenance tables for continued scheduled maintenance. Consult the Genie Industries Service Department for instructions on how to safely remove the boom When removing a hose assembly assembly from the machine. Do not allow oil to squirt or spray.
How to Remove the Platform Rotator Component damage hazard. Illustration 3 22 Step on the footswitch at the platform. Continued use of an improperly calibrated platform overload system could result in the system failing to sense an overloaded platform. Continue holding the toggle switch until air stops coming out of the bleed screw. However, continuous improvement of our products is a Genie policy.
Genie S-80 and S-85 Service Manual from serial number 101 to 785. You will then be emailed an order confirmation and tracking number when it becomes available. Spraying hydraulic oil can penetrate and burn skin. The max-out settings on the joystick can be changed to compensate for hydraulic pump wear to maintain peak performance from the machine. Cap the fittings on the cylinder. Properly functioning coil diodes protect How to Test a Coil the electrical circuit by suppressing voltage spikes.
Failure to install the fastener into the engine tray anchor hole to secure the engine tray from moving could result in death or serious injury. Be careful not to damage the counterbalance valves on the primary boom extension cylinder when removing the cylinder from the boom. If a joystick is disconnected or replaced, it must be calibrated before that particular machine function will operate. Continued use of an improperly operating safety envelope could result in the system not restricting the range of motion. Result: The drive enable indicator light should come on and remain on while the boom is anywhere in the range shown. If we can provide additional assistance of any kind, please feel free to contact us and tell us what you need.
Contact with electrically charged circuits could result in death or serious injury. Proper key switch action and response is essential to safe machine operation. They are available in the O-ring field service kit Genie part number 49612. Result: If water is present in the filter bowl continue with steps 4 through 8. Indicates that an incorrect result has occurred after performing a series of steps. The method to reengage the carriage depends on the model of garage door opener you own. The boom lift cylinder is equipped with counterbalance valves to prevent movement in the event of a hydraulic line failure.
Lay all hoses and cables to the side. Carefully lift the counterweight upwards and remove the counterweight from the machine. If you have problems finding what you need you can always call us and we will ship you the parts. The battery is fully charged. If boom toggle switch to the down position, hold the hydraulic oil is not replaced for a moment and then release it.
Preliminary setting: turn low idle adjustment screw clockwise all the way in. Maintaining the tires and wheels in good condition, including proper wheel fastener torque, is essential to safe operation and good performance. Genie specifications require that this procedure be performed every 100 hours or monthly, whichever comes first. Result: All battery cells display an adjusted specific gravity of 1. Be sure to wear protective eye wear and other protective clothing if the situation warrants it. If rpm adjustment or service is required, please contact the Genie Industries Service Department. Do not remove Genie part number 84443 them.
Refer to the Operator's Manual on your machine. Function tests are designed to discover any malfunctions before the machine is put into service. Note: The brakes must be able to hold the machine on any slope it is able to climb. The free-wheel valve should always remain closed. Used to indicate the presence of a.
These components may fail if they are used a second time. Wiring diagrams are usually included. Be aware of potential crushing hazards such as moving parts, free swinging or unsecured components when lifting or placing loads. Do not remove the pins. Record the time it takes for that function to complete a full cycle ie; boom up.