If the handshake frequency is not given or is not understood by the panel, the panel will not send its message. If so, wait a few minutes, and try again. The security keypad and remote keypad should be tested as well. The alpha display keypad will display the first of a series of prompts. Install transmitters in accordance with the instructions provided with each. Select the maximum amount of time in which two cross zones must be tripped in an armed system to send an alarm message to the Central Station.
Manually enter the 7-digit serial number printed on the label of the transmitter. Disarming before the end of the entry delay stops alarm sounding and no message is sent to the central station. Each of the inputs requires its own programming zone e. If unsuccessful, the system makes up to 8 attempts to send all reports to the secondary number. As the system receives a signal from each transmitter, the zone number of that transmitter disappears from the display. Enter the appropriate value for each entry, 1-10, based on 3.
Enter up to 16 optional characters, which may be sent as a Configurable Zone Type Options prefix to the 7-digit system status code sent to Pager 1 if used. You must plug the transformer in first, and then connect the battery. This control does not automatically reset power to 4-wire smoke detector zones, so you must use a relay e. System Test With the system in the disarmed state, check that all zones are intact not faulted. Keyswitch Wiring ConnectionsConnecting Relay Modules1. Enter the zone event that will activate this output. Side question maybe different thread , short of buying a 2 line keypad, would the downloadable programming application help in this case and dial in to the panel to update? The following table shows the available zone lists and their purposes: List No.
Insert the key into the lock. Vent Zone entry 2 Zones set for this option are ignored if faulted when arming the system, but are protected if the zone is later restored e. Many of the Ademco models listed at the top of this article are now discontinued and out of production. This is a tan-colored metal box about 18 inches square. Remove the cabinet knockouts needed for wiring entry.
Repeat the previous steps to enter the descriptor for the next zone. The phone module will now seize the line, and 2 long tones sound, followed by the usual voice prompt for the access code. Thanks again for your help, wished I read this before, but it looks like the sequence was different. Upon entering the system test mode, the outside sounder should sound for 1 second. Panel Trigger Mode: Voice session starts automatically following delivery of alarm report. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company.
The system is in communication with the central station for change of function or status verification. Each key can be programmed for 24-hour Silent, 24-hour Audible, Fire, or Personal Emergency responses. Thanks for the help as always, this is turning into a nice self-monitoring setup. It's also not unusual for drywall installation to damage the wiring at the contacts. Expanded Formats The first digit is displayed on the first line.
Keypads are identified by predefined addresses starting at address 16. This site is supported through affiliate marketing. If the tamper is opened when the system is armed, an alarm will occur. These quotes are absolutely free! For wired devices, return to the initial summary screen prompt to begin programming the next zone. If using latchkey pager report, define the latchkey report monitoring zone option is used which pauses calls. This mode is similar to the Transmitter Test mode, except that the wireless receiver gain is reduced.
Temporal pulse sounding for a fire alarm Figure 5. However, some fields must be programmed for each particular installation to establish its specific alarm and reporting features. You may freely link to this site, and use it for non-commercial use subject to our. If this procedure is not followed, phone module operation will not be possible. Les réparations de matériel nomologué doivent être coordonnées par un représentant désigné par le fournisseur. .
Look inside the main panel lid for a sticker. The display will clear after you correct the programming. The phone module will not provide annunciation of any other words. It will often be located near the main panel box, but could also be in the ceiling outlet for the garage door opener. Bypass Armed entry 4 Zones set for this option can be bypassed when the system is armed. Sound ends when exit time expires. To program pager reporting, do the following: 1.
Swing the base of the board into the mounting clips and secure it to the cabinet with the accompanying screws. The system will check for duplicate. Enter next sensor or 00 to exit 12. The alpha display keypad will display the first of a series of prompts. To set up the control panel, do the following: 1. Enter the primary phone and secondary phone numbers.